monstershop.co.uk
Instructions by monstershopBuilders Trestle Stand
Builders Trestle Stand Builders Trestle Stand Before you start Safety GPSR Information Parts Steps 1. Prep the two side frames 2. Install the vertical bars 3. Connect the side frames with the bottom bar 4. Fit the top bar 5. Install the tool rack and hook 6. Install the support feet Section 7 No results monstershop / Builders Trestle Stand Instructions by monstershop Builders Trestle Stand Trestle stand for construction Product Information Builders' Trestle Board Stand Our premium Builders’ Trestle Board Stand is engineered for strength, stability, and reliable performance across all types of construction and maintenance work. Built from heavy-duty steel with adjustable height and levelling feet, it provides a secure and adaptable platform on any jobsite. An integrated tool tray keeps essential equipment within easy reach, delivering improved efficiency and convenience throughout the workday. SKU 216672,216586,216587,216673,216588,216591,216593 Dimensions 100 (L) x 60 (W) x 100-180 (H) cm Weight 8kg Materials Steel Frame, Plastic Feet GPSR Information UK Manufacturer: Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG Person Responsible: Rana Harvey, Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England, +441347878880 EU Manufacturer: Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL Netherlands +441347878880 Person Responsible: Rana Harvey, Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL, Netherlands, +44134787888 Safety Ensure you have read and fully understood the instruction manual and safety advice before using this product. Do not exceed the maximum load capacity of 200kg per stand; overloading may result in structural failure or collapse. Ensure all locking pins, chains, and mechanical securing mechanisms are properly fastened and checked before each use. Only use the trestle stands on firm, level ground to prevent tipping or collapse. Avoid applying sideways pressure to the stands; do not lean ladders, boards, or heavy materials against them. If lateral force cannot be avoided due to usage demands, secure or anchor the stands appropriately to a fixed structure or surface. Keep hands, fingers, and clothing clear of pinch points and moving joints during setup, height adjustment, and dismantling to avoid injury. Always wear suitable protective gloves when adjusting the stand height or assembling the unit. Place trestle stands in positions that do not obstruct walkways or high-traffic areas to prevent tripping hazards. Use high-visibility tape or markers on the base legs if the product is used in dim or low-light conditions. Do not modify the structure or components in any way; use only as intended by the manufacturer. Ensure any tools placed on built-in holders or trays are stable and will not fall during use; do not overload tool holder shelves. Ensure the product is fully collapsed to the lowest height when not in use to prevent accidental injury or obstruction. Do not allow children or untrained individuals to use or handle the trestle stands. Maintain a clear working environment around the product at all times and avoid clutter that could cause instability. Do not use this product for any purpose other than its intended design, such as supporting temporary work surfaces or structures under safe, controlled conditions. In multi-user or shared environments, implement and follow a usage log or inspection record system to ensure ongoing safety compliance. GPSR Information UK Manufacturer: Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England. Person Responsible: Rana Harvey, Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England. +441347878880 EU Manufacturer: Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL Netherlands. Person Responsible: Rana Harvey, Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL, Netherlands. +441347878880 Parts 1Top Bar 2Vertical bar with stand 3Side Extension Bar 4 Central Bar 5Foot 6Screw M6x40 7Washer 06 8Nut M6 9Tool Tray 10Locking Screw 11Hook 12Chain Locking device 13Screw M5x45 14Nut M5 1. Prep the two side frames 1. Put the two support leg frames (2) on the floor, parallel to each other, with the open tops facing upward (where the top bar will sit). 2. Install the vertical bars 1. Insert the two vertical straight bars (3) into the upper sockets/holders on the support leg frames (2) (one vertical bar per side frame). 2. Secure each vertical bar (3) to its support leg frame (2) using the Locking Screw (10) and Locking Device (12) in the holes shown for that joint. 3. Connect the side frames with the bottom bar 1. Fit the bottom horizontal straight bar (4) between the two side frames (2), aligning the holes. 2. Bolt it in place using M6×40 screws (6) with washers (7) and M6 nuts (8) at each end. 4. Fit the top bar 1. Place the top bar (1) across the tops of the two vertical bars (3). 2. Secure the top bar (1) to each vertical bar (3) using M6×40 screws (6) + washers (7) + M6 nuts (8). 5. Install the tool rack and hook 1. Attach the tool rack (9) in the position shown. 2. Fix it using the indicated M6 hardware (6, 7, 8). 3. Attach the hook (11) to the rack/position shown, using the indicated fastener points. 6. Install the support feet 1. Screw the support feet (5) onto the bottoms of the support leg frames (2) 2. Adjust them so the stand sits flat and doesn’t rock. 7. Inspect regularly: Check the frame, welds, and adjustment mechanisms for signs of wear, cracks, or distortion before each use. Keep joints and moving parts clean: Remove dirt, dust, and debris from hinges, locking pins, and adjustment points, and lightly oil them to ensure smooth operation. Protect against corrosion: Wipe down the stand after exposure to moisture and store it in a dry area to prevent rust; apply a rust-inhibiting spray if needed. Tighten components: Periodically check all bolts, screws, and locking mechanisms to ensure they remain secure and functional. Store the trestle stands in a dry, sheltered environment to prevent corrosion and damage from weather exposure. monstershop (opens in new tab)Terms (opens in new tab)Privacy (opens in new tab)

Instructions by

monstershop

Builders Trestle Stand

Trestle stand for construction

Product Information

Builders' Trestle Board Stand

Our premium Builders’ Trestle Board Stand is engineered for strength, stability, and reliable performance across all types of construction and maintenance work. Built from heavy-duty steel with adjustable height and levelling feet, it provides a secure and adaptable platform on any jobsite. An integrated tool tray keeps essential equipment within easy reach, delivering improved efficiency and convenience throughout the workday.

SKU: 216672,216586,216587,216673,216588,216591,216593
Dimensions: 100 (L) x 60 (W) x 100-180 (H) cm
Weight: 8kg
Materials: Steel Frame, Plastic Feet

GPSR Information

Manufacturer: Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG
Person Responsible: Rana Harvey, Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England, +441347878880

Manufacturer: Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL Netherlands +441347878880
Person Responsible: Rana Harvey, Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL, Netherlands, +44134787888

Safety

Ensure you have read and fully understood the instruction manual and safety advice before using this product.

Do not exceed the maximum load capacity of 200kg per stand; overloading may result in structural failure or collapse.

Ensure all locking pins, chains, and mechanical securing mechanisms are properly fastened and checked before each use.

Only use the trestle stands on firm, level ground to prevent tipping or collapse.

Avoid applying sideways pressure to the stands; do not lean ladders, boards, or heavy materials against them.

If lateral force cannot be avoided due to usage demands, secure or anchor the stands appropriately to a fixed structure or surface.

Keep hands, fingers, and clothing clear of pinch points and moving joints during setup, height adjustment, and dismantling to avoid injury.

Always wear suitable protective gloves when adjusting the stand height or assembling the unit.

Place trestle stands in positions that do not obstruct walkways or high-traffic areas to prevent tripping hazards.

Use high-visibility tape or markers on the base legs if the product is used in dim or low-light conditions.

Do not modify the structure or components in any way; use only as intended by the manufacturer.

Ensure any tools placed on built-in holders or trays are stable and will not fall during use; do not overload tool holder shelves.

Ensure the product is fully collapsed to the lowest height when not in use to prevent accidental injury or obstruction.

Do not allow children or untrained individuals to use or handle the trestle stands.

Maintain a clear working environment around the product at all times and avoid clutter that could cause instability.

Do not use this product for any purpose other than its intended design, such as supporting temporary work surfaces or structures under safe, controlled conditions.

In multi-user or shared environments, implement and follow a usage log or inspection record system to ensure ongoing safety compliance.

Parts

1Top Bar

2Vertical bar with stand

3Side Extension Bar

4 Central Bar

5Foot

6Screw M6x40

7Washer 06

8Nut M6

9Tool Tray

10Locking Screw

11Hook

12Chain Locking device

13Screw M5x45

14Nut M5

1. Prep the two side frames

1. Put the two support leg frames (2) on the floor, parallel to each other, with the open tops facing upward (where the top bar will sit).

2. Install the vertical bars

1. Insert the two vertical straight bars (3) into the upper sockets/holders on the support leg frames (2) (one vertical bar per side frame).
2. Secure each vertical bar (3) to its support leg frame (2) using the Locking Screw (10) and Locking Device (12) in the holes shown for that joint.

3. Connect the side frames with the bottom bar

1. Fit the bottom horizontal straight bar (4) between the two side frames (2), aligning the holes.
2. Bolt it in place using M6×40 screws (6) with washers (7) and M6 nuts (8) at each end.

4. Fit the top bar

1. Place the top bar (1) across the tops of the two vertical bars (3).
2. Secure the top bar (1) to each vertical bar (3) using M6×40 screws (6) + washers (7) + M6 nuts (8).

5. Install the tool rack and hook

1. Attach the tool rack (9) in the position shown.
2. Fix it using the indicated M6 hardware (6, 7, 8).
3. Attach the hook (11) to the rack/position shown, using the indicated fastener points.

6. Install the support feet

1. Screw the support feet (5) onto the bottoms of the support leg frames (2)
2. Adjust them so the stand sits flat and doesn’t rock.

7.

Inspect regularly: Check the frame, welds, and adjustment mechanisms for signs of wear, cracks, or distortion before each use.

Keep joints and moving parts clean: Remove dirt, dust, and debris from hinges, locking pins, and adjustment points, and lightly oil them to ensure smooth operation.

Protect against corrosion: Wipe down the stand after exposure to moisture and store it in a dry area to prevent rust; apply a rust-inhibiting spray if needed.

Tighten components: Periodically check all bolts, screws, and locking mechanisms to ensure they remain secure and functional.

Store the trestle stands in a dry, sheltered environment to prevent corrosion and damage from weather exposure.