{
  "schema": "stepacross.manual.v1",
  "slug": "grp-electrical-enclosure",
  "lang": "en",
  "title": "GRP Electrical Enclosure (H800mm x W530mm)",
  "description": "This guide provides step-by-step instructions for assembling components and using the GRP Electric Enclosure (H800mm x 530mm)",
  "status": "public",
  "chapters": [
    {
      "infos": [
        {
          "title": "Safety Advice\n",
          "text": "* Only qualified and competent electrical personnel should access internal components or perform installation or servicing.\n* Always isolate and fully disconnect the power supply before opening or servicing the enclosure to prevent risk of electric shock.\n* Do not use this product for any purpose other than housing approved electrical equipment as specified by the manufacturer.\n* Ensure the enclosure is securely mounted according to the installation instructions; improper installation can result in injury, equipment failure, or property damage.\n* Wall or surface mount only on structurally sound and level surfaces capable of supporting the weight of the enclosure and internal components.\n* Observe the maximum permitted load of internal mounting surfaces; do not overload the DIP rails or plywood mounting plate.\n* Use appropriate tools and follow PPE requirements (e.g. protective gloves and eye protection) when handling GRP surfaces to avoid cuts or irritation from sharp edges or fibreglass splinters.\n* Do not drill or mechanically alter the enclosure; doing so may compromise protection ratings (IP/IK) and void warranty or compliance.\n* Avoid obstruction of internal ventilation space; do not pack the enclosure tightly with components that may lead to overheating.\n* Do not obstruct cooling air circulation during operation; ensure ambient conditions meet enclosure specifications.\n* Allow components to cool down before conducting maintenance or inspection to prevent burns or heat-related injury.\n* Ensure the inner door and main door are closed and latched securely using the swing handle lock and 3-point mechanism after installation or maintenance to ensure weather and dust resistance; failure to do so may cause internal damage or electrical hazards.\n* Always check that the waterproof PVC warning label remains clearly visible and intact; replace it if damaged.\n* Confirm that the protection ratings match the intended location and mechanical exposure risks.\n* Suitable for outdoor and indoor use; however, enclosure must be installed in locations protected from excessive vibration or mechanical impact beyond its rated IK level.\n* Avoid placing the unit in direct contact with standing water or buried in the ground; the enclosure is not rated for submersion or underground installation.\n* Do not use the enclosure in environments containing flammable gases, explosive dusts, or corrosive chemicals unless explicitly certified for such use.\n* Ensure all cable entries, glands, and fittings are sealed using IP-rated components compatible with the enclosure material.\n* Check that mounting height avoids creating trip hazards or restricted access pathways; install only where it will not impede movement or emergency routes.\n* The enclosure must not be accessed or opened by unauthorised persons; keep the key cylinder secured and access controlled at all times.\n* Never force open the door or locking mechanism; if damaged, consult the manufacturer for replacement parts.\n* Periodically inspect the enclosure for signs of wear, corrosion of fixings, UV degradation, or seal failure; repair or replace components as needed.\n* This product is not a toy and must be kept out of reach of children or vulnerable persons; contains small parts and sharp edges that may cause injury.\n* Do not attempt to dispose of the enclosure in general waste; it must be disposed of according to local electronic equipment and fibreglass recycling regulations.\n* Product traceability information must be retained and remain affixed or recorded for recall and safety purposes.\n\n",
          "type": "Safety"
        },
        {
          "title": "GPSR Information\n",
          "text": "**UK**\n\n* **Manufacturer:** Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England.\n* **Person Responsible:** Rana Harvey, Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England. +441347878880\n\n**EU**\n\n* **Manufacturer:** Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL Netherlands.\n* **Person Responsible:** Rana Harvey, Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL, Netherlands. +441347878880\n",
          "type": "Gpsr"
        }
      ],
      "steps": [],
      "sections": [
        {
          "images": [],
          "title": "Step 1 - The Lock\n",
          "description": "* To lock the GRP door, turn the key by 90 degrees to the left and into a vertical position.\n* To unlock the GRP door, turn the key 90 degrees to the right and into a horizontal position.\n\n<br />\n\nNote: Press your hand down onto the door when turning the key.\n"
        },
        {
          "images": [],
          "title": "Step 2 - Din Rails\n",
          "description": "* To disassemble the din rails, use a M6 spanner to unscrew the 2 nuts in an anti-clockwise direction.\n* To install the din rails, place the rail into the correct position and screw the 2 nuts with the bolts in a clockwise direction, using a M6 spanner.\n\n"
        },
        {
          "images": [],
          "title": "Step 3 - The Mounting Plate\n",
          "description": "* To disassemble the mounting plate, use an M6 spanner to unscrew the 4 nuts in an anti-clockwise direction.\n* To install the mounting plate, place the plate into the correct position, and use an M6 spanner to screw in the 4 nuts and bolts in a clockwise direction.\n\n"
        },
        {
          "images": [],
          "title": "Step 4 - The Wall Mounting Brackets\n",
          "description": "* Drill through the holes in the wall mount.\n\n* Place the nut in the correct position of the wall mounting bracket.\n\n* Install the wall mounting pendant into the hexagonal mounting hole so you can easily adjust its angle (horizontal, vertical, or 45°). Use mounting distance A2 (H×W) for vertical installation and A1 (H×W) for horizontal installation, as specified in the data sheet.\n\n* Insert the bolts and fix the nuts to the brackets.\n\n* Repeat this for the remaining 3 corners.\n\n* Select a suitable position to fix the box to the wall.\n\n<br />\n\n**Please note:** It is the installer’s responsibility to verify suitability for the intended mounting surface and load. The manufacturer accepts no liability for failure resulting from inappropriate fixings.\n"
        },
        {
          "images": [],
          "title": "Maintenance\n",
          "description": "* Clean the exterior using a soft cloth and mild detergent; avoid harsh chemicals or abrasive tools that may degrade the GRP or PVC label.\n* Inspect door seals and locking mechanisms quarterly to ensure continued IP protection; replace seals showing signs of cracking or wear.\n* Re-tighten all mounting hardware and check for enclosure movement or instability during routine maintenance checks.\n* Check warning label visibility during every inspection cycle; ensure replacement labels are waterproof and compliant with original specifications.\n* Schedule internal inspections at least annually, or more frequently in harsh environments, to identify any signs of electrical wear or enclosure compromise.\n* Always use compatible fixings and gaskets when replacing or adding components to preserve enclosure integrity.\n\n"
        },
        {
          "images": [],
          "title": "Troubleshooting\n",
          "description": "**WHAT DO I DO IF THERE ARE MISSING PARTS FROM MY ORDER?**\n\nIf there appears to be any part missing from your order, contact our friendly and helpful Customer Support Team within 7 days of receipt.\n"
        }
      ],
      "materials": {
        "items": [
          {
            "name": "Bolts"
          },
          {
            "name": "Nuts"
          },
          {
            "name": "Din Rails"
          },
          {
            "name": "Mounting Plate"
          },
          {
            "name": "Key"
          }
        ],
        "title": "Parts"
      },
      "productInfo": {
        "characteristics": [
          {
            "label": "SKU",
            "value": "217293"
          }
        ],
        "variations": [
          {
            "name": "Specifications:",
            "value": "Attribute:"
          },
          {
            "name": "External Dimensions:",
            "value": "800 x 600 x 300mm"
          },
          {
            "name": "Internal Dimensions (Door to Mounting Plate):",
            "value": "754 x 577 x 275mm"
          },
          {
            "name": "Internal Size including mounting plate",
            "value": "750 x 542 x 250mm"
          },
          {
            "name": "Wall mounting Distance A1",
            "value": "727.5 x 633"
          },
          {
            "name": "Wall mounting Distance A2",
            "value": "811 x 549.5"
          },
          {
            "name": "Net Weight:",
            "value": "14.5KG"
          },
          {
            "name": "Gross Weight:",
            "value": "16.5KG"
          },
          {
            "name": "Materials:",
            "value": "SMC Fiberglass, Plywood, Metal Hardware and DIP Rails, Plastic Accessories"
          },
          {
            "name": "IP Level:",
            "value": "IP66"
          },
          {
            "name": "IK Level:",
            "value": "IK09"
          }
        ],
        "name": "GRP Electrical Enclosure (H800mm x W530mm)",
        "description": "Thank you for choosing T-MECH’s GRP electrical enclosures. These models are designed to offer secure, long-lasting protection for your electrical components. Built from durable glass-reinforced plastic, it features an internal door and integrated DIP rails for easy equipment installation and organisation, helping to keep internal systems safe from dust, water, and accidental impact.\n"
      }
    }
  ],
  "cover": {
    "title": "GRP Electrical Enclosure (H800mm x W530mm)",
    "description": "This guide provides step-by-step instructions for assembling components and using the GRP Electric Enclosure (H800mm x 530mm)",
    "image": {
      "path": "images/946ca644e4b3d20f.png",
      "alt": ""
    }
  }
}