Petnamic Rabbit Run

This guide provides step-by-step instructions for assembling components and using your Petnamic Rabbit Run.

Product Information

The Petnamic Rabbit Run is a 6 ft wooden enclosure designed to provide rabbits with a secure exercise area. It features a folding, collapsible design, two access doors and a supplied waterer.

SKU	218848
Length	181cm
Width	100cm
Height	48.5cm
Weight	9.5kg
	Foldable Design
Includes	250ml Waterer

Petnamic Rabbit Run

EN

Safety Information

Safety Advice

Ensure you have read and fully understood the instruction manual and safety advice before using this product.
For pet rabbits only. This product is an animal enclosure and must not be used for any other purpose.
Adult assembly and supervision are required. Keep children away during assembly, folding, moving and maintenance, and do not allow children to climb or play on the run.
Assemble the run fully before use and ensure all hinges, locking points, fasteners, doors and catches are correctly fitted and securely engaged.
Finger-trapping hazard: keep hands and fingers clear of hinges and folding joints. Fold and unfold the run slowly and keep children and animals clear.
Inspect the timber before assembly and each use for cracks, splits, splinters, excessive chewing or other damage. Do not use damaged or structurally weakened components.
Wire mesh, staples and fixings may have sharp edges. Handle carefully and wear suitable protective gloves during assembly or maintenance where necessary.
Inspect the mesh regularly. Do not use the run if mesh is damaged, detached or has exposed sharp edges; repair or replace damaged components before use.
Position the run on firm, stable and level ground. Ensure the structure is stable and fully opened before placing rabbits inside.
Secure the run appropriately where there is a risk of movement or lifting. Do not use during high winds or severe weather and move rabbits to a safe indoor location during adverse conditions.
Check both access doors and catches before every use. Keep them fully secured whenever rabbits are inside to reduce the risk of escape.
Inspect the enclosure for openings or damage that could allow rabbits to escape or predators to enter. Position it away from known predators and do not leave vulnerable animals unattended for extended periods.
Rabbits may chew the timber. Regularly check for damaged wood, loose or protruding fixings and weakened sections. Remove the run from use until unsafe damage has been repaired or affected components replaced.
Securely attach the supplied waterer and provide clean, fresh drinking water. Before each use, check that water flows freely from the nozzle and that the bottle is not empty, leaking or blocked to reduce the risk of dehydration.
Regularly inspect the waterer, cap and nozzle. Do not use cracked, loose or damaged parts, as detached or damaged components could cause injury or present an ingestion/choking hazard.
Do not sit, stand or climb on the run or place heavy objects on top of it.
Keep the wooden run away from naked flames, burning materials and sources of intense heat.
Use safe lifting techniques when moving the run and obtain assistance where necessary. Do not move or fold the enclosure while rabbits are inside.
Before every use, check the frame, timber, mesh, hinges, doors, catches, folding joints, fixings and waterer. Stop using the product if any component is loose, missing, damaged or unsafe.
Store the folded run securely in a dry location where it cannot fall or unexpectedly unfold, and keep it away from children and animals.
Dispose of the product responsibly in accordance with local waste and recycling requirements, taking care with sharp or damaged components.

GPSR Information

UK GPSR Information

Manufacturer Monster Group UK Limited
Monster House 19-23 Alan Farnaby Way
Industrial Estate Sheriff Hutton
York YO60 6PG
England
+441347878880

Representative Rana Harvey
Monster House 19-23 Alan Farnaby Way
Industrial Estate Sheriff Hutton
York YO60 6PG
England
+441347878880

EU GPSR Information

Manufacturer Monster Group BV
Van Heemskerckweg 28A & B
-
Venlo 5928LL
Netherlands
+441347878880

Representative Rana Harvey
Van Heemskerckweg 28A & B
-
Venlo 5928LL
Netherlands
+441347878880

Included Parts

1x Part A - Rabbit Run Enclosure

1x Part B - Lid

8x Part P1 - M6*60 Bolts

12x Part P2 - M3*16 Screws

2x Part P3 - Latch

1x Part P4 - 250ml Waterer

Monster Manual

Assembly

1.

Pull on either end of the Rabbit Run Enclosure (Part A) until the sides are straight.

2.

Lie the lid (Part B) flat on top of the enclosure.
Secure into place using P1 bolts.

3.

Attach the latch on either end of the Rabbit Run using the P2 screws.

4.

Fill the waterer and attach to the outside of the rabbit run, with the nozzle through the mesh to allow the rabbits to drink from it.

Maintenance

Clean the enclosure regularly and remove animal waste and contamination. Allow the timber to dry before storage.
Regularly clean the supplied waterer and nozzle and check that water flows correctly before use.
Periodically check and tighten fixings and inspect the timber, mesh, doors, catches and hinges for wear, chewing or damage.
Do not use the run until any damage affecting stability, containment or animal/user safety has been properly repaired.

Troubleshooting

Please read through the guide below if you have any issues or faults with your device. The information covers and resolves the majority of frequently asked questions.

Q: There are parts missing from my order.

A: If there appears to be any part missing from your order, contact our friendly and helpful Customer Support Team within 7 days of receipt.

For all other issues please contact our Customer Support department via the details on the Contact page.