{ "schema": "stepacross.manual.v1", "slug": "t-mech-artificial-grass-vacuum-", "lang": "en", "title": "T-Mech Artificial Grass Vacuum", "description": "Refresh your artificial grass with the T-Mech garden vacuum. With a 3500RPM brush, 5 height settings, 50L bag, and 1800W suction, it removes debris and lifts fibres with ease. Self-propelled, lightwei", "status": "public", "chapters": [ { "infos": [ { "title": "Safe Working Practice", "text": "* Ensure you have read and fully understood the instruction manual and safety advice before using this product.\n* Do not use this product for anything other than its intended purposes.\n* **ATTENTION!** This product must not be used on gravel or loose stone surfaces, garden borders, hedges, or bushes.\n* Do not immerse this product in water.\n* Do not operate this product with wet hands or in damp conditions.\n* After use, ensure the product is switched off properly and safely.\n* Inspect the product and its power cable for signs of damage. Do not use if there are signs of damage.\n* We recommend the use of an RCD with this product.\n* Do not attempt to remove items that may have become entangled in the brush head until you have turned off and unplugged the product.\n* Do not place hands or feet near to the brush head whilst operating the product.\n* Do not open the rear cover during use.\n* Check the work area for potential dangers before using the product.\n* Only use the product in good visibility.\n* Wear solid footwear and long trousers when operating the product.\n* Only operate this product at walking speed.\n* Do not leave this product unattended whilst it is operational.\n* Turn the product off if it starts to produce excessive heat or noise. Leave for at least one hour before turning on the product.\n* Ensure that hot ashes, lit cigarettes, matches, gas lighters or any similar items are not allowed to enter the product.\n* The product includes a 50 litre collection basket. Please empty regularly and do not allow to become over full.\n* Do not try to repair this product yourself. All repairs should be conducted by a qualified technician.\n* Clean the product after every use.\n* Always adhere to local noise restrictions. The maximum noise level generated by this product is detailed in the Product Specifics section of the manual.\n* We recommend the use of ear protectors whilst using this product. Do not try to repair this product yourself. All repairs should be conducted by a qualified technician.", "type": "Safety" }, { "title": "Motor Strain", "text": "Do not place too much strain on the motor when working in demanding conditions. If the motor is put under excessive strain, you will hear a change in the motor noise as its speed reduces. If this happens, stop working and raise the brush depth to reduce the load on the motor. Continued use of the vacuum with the motor under strain may damage the vacuum.", "type": "Safety" }, { "title": "GPSR Information\n", "text": "**UK**\n\n* **Manufacturer:** Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England.\n* **Person Responsible:** Rana Harvey, Monster Group UK Limited, Monster House 19-23 Alan Farnaby Way, Industrial Estate Sheriff Hutton, York YO60 6PG, England. +441347878880\n\n**EU**\n\n* **Manufacturer:** Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL Netherlands.\n* **Person Responsible:** Rana Harvey, Monster Group BV, Van Heemskerckweg 28A & B, Venlo 5928LL, Netherlands. +441347878880\n\n", "type": "Gpsr" } ], "steps": [ { "number": 1, "description": "**A.** Vacuum\n\n**B.** Handle Bottom Section\n\n**C.** Handle Middle Section\n\n**D.** Handle Top Section\n\n**E.** Quick Release Levers\n\n**F.** Handle Screws\n\n**G.** Power Cable Retaining Bracket\n\n**H.** Power Cable Clip\n\n**I.** Collection Basket\n\n**J.** Brush Height Adjustment Lever\n\n**K.** Starting Lever\n\n**L.** Safety Button", "images": [ { "path": "images/afa07734f0e3fed0.jpg", "alt": "" } ], "title": "Product Features" }, { "number": 2, "description": "Attach the lower section of the handle (B) using the two handle screws (F) on both sides. Adjust the handle angle to your preference using the spline connector (K).", "images": [ { "path": "images/5797a5ce21603665.jpg", "alt": "" } ], "title": "Attaching the Lower Handle Section" }, { "number": 3, "description": "Slide the Power Cable Retaining Bracket (G) over the Handle Middle Section (C). Then attach the Handle Middle Section to the Handle Bottom Section using two quick release levers (E).", "images": [ { "path": "images/e035191780ad9735.jpg", "alt": "" } ], "title": "Assembling the Handle Middle Section" }, { "number": 4, "description": "Attach the Handle Top Section (D) to the Handle Middle Section using two Quick Release Levers (E).", "images": [ { "path": "images/baaf5dcbadc4b6b0.jpg", "alt": "" } ], "title": "Attaching the Handle Top Section" }, { "number": 5, "description": "Attach the power cable to the handle using the Power Cable Clip (H).", "images": [ { "path": "images/5f0ba61071c1e15a.jpg", "alt": "" } ], "title": "Securing the Power Cable" }, { "number": 6, "description": "Place the Collection Basket Frame (I) into the Textile Collection Basket (J) and attach all fasteners to the left, right, and rear poles of the frame. Make sure that all fasteners are secured correctly.", "images": [ { "path": "images/be73821a86a672c9.jpg", "alt": "" } ], "title": "Assembling the Collection Basket" }, { "number": 7, "description": "1. Lift up protective cover.\n2. Make sure that the ejection chute is clear and free of debris.\n3. Place the fully assembled collection basket onto the fastening points in the rear part of the chassis.\n4. Place the protective cover on top of the collection basket and check it is seated correctly.", "images": [], "title": "Attaching the Collection Basket to the Vacuum" }, { "number": 8, "description": "1. Press and hold the Safety Button (L).\n2. Pull the Starting Lever (K) towards the handle.\n3. Release the Safety Button.", "images": [ { "path": "images/70ac32b777f81f1d.jpg", "alt": "" } ], "title": "Starting the Vacuum" }, { "number": 9, "description": "Release the Starting Lever.", "images": [], "title": "Stopping the Vacuum" }, { "number": 10, "description": "* **Level 1:** +6 mm Brush Height\n* **Level 2:** -3 mm Brush Height\n* **Level 3:** -6 mm Brush Height\n* **Level 4:** -9 mm Brush Height\n* **Level 5:** -12 mm Brush Height", "images": [], "title": "Adjusting the Brush Head Height" }, { "number": 11, "description": "This vacuum is protected by a safety mechanism which is activated if the motor is overloaded, or the brush head is caught and cannot freely rotate. The safety mechanism will shut off the vacuum until the safety mechanism is reset.\n\n**To reset the mechanism:**\n\n* Release the starting handle and unplug the vacuum.\n* Check the vacuum for any obstructions and remove if required.\n* Wait a few minutes and you can then restart the vacuum.\n* Do not press the starting handle while waiting as this will extend the safety mechanism reset time.", "images": [], "title": "Safety Cut-Out Reset" }, { "number": 12, "description": "* Always unplug the vacuum from the power supply before undertaking any maintenance.\n* The vacuum should be cleaned after every use.\n* Do not clean this vacuum under running water and do not use a pressure washer.\n* Do not use hard or pointed items for cleaning the vacuum.\n* Regularly remove accumulated debris from the wheels, brush head and cover.\n* Regularly check the vacuum for damage. If any damage is found, do not use the vacuum, and arrange for repair.", "images": [], "title": "Maintenance" }, { "number": 13, "description": "**Note:** We recommend wearing gloves when replacing the brush head.\n\n1. Disconnect the vacuum from the power supply.\n2. Unscrew the brush head securing bolt (1) on the underside of the chassis.\n3. Lift the brush at an angle and pull out.\n4. Slide the replacement brush on to the drive shaft so that the guide pin on the brush head lines up with the corresponding part of the drive shaft.\n5. Retighten the securing bolt (1) to secure the brush head.", "images": [ { "path": "images/8e4f981a2fcd70c4.jpg", "alt": "" } ], "title": "Replacing the Brush Head" }, { "number": 14, "description": "* **WHAT DO I DO IF THERE ARE MISSING PARTS FROM MY ORDER?**\n\nIf there appears to be any part missing from your order, contact our friendly and helpful Customer Support Team within 7 days of receipt.\n\n* **WHAT DO I DO IF THE VACUUM WON’T TURN ON?**\n\nFirst, check the vacuum is plugged into the power supply and there is no damage to the power cable or fuses. Also, ensure you are pressing the safety button before you pull the starting lever. If this doesn’t resolve the problem, please call the Customer Support Team. Details on the Contact Us page.\n\n* **WHY IS THE VACUUM NOT PICKING UP DEBRIS?**\n\nTry lowering the brush head closer to the surface. If this does not resolve the issue, then check that the collection basket is not full and empty if required. Also, check that there is not excessive debris entangled in the brush head and clean if required.\n\n**FOR ALL OTHER ISSUES, PLEASE CONTACT OUR CUSTOMER SUPPORT TEAM.**", "images": [], "title": "Resolution Guide" } ], "sections": [], "materials": { "items": [ { "name": "A - Vacuum Body" }, { "name": "B - Handle Bottom Section" }, { "name": "C - Handle Middle Section" }, { "name": "D - Handle Top Section" }, { "name": "E - Quick Release Levers" }, { "name": "F - Handle Screws" }, { "name": "G - Power Cable Retainer Bracket" }, { "name": "H - Power Cable Clip" }, { "name": "I - Collection Basket Frame" }, { "name": "J - Textile Collection Basket" }, { "name": "K - Spline Connector" } ], "title": "Materials" }, "tools": { "items": [ { "name": "RCD (Residual Current Device)" }, { "name": "Ear protectors" }, { "name": "Gloves" } ] }, "productInfo": { "characteristics": [ { "label": "SKU", "value": "210299" } ], "variations": [ { "name": "Specifications", "value": "Details" }, { "name": "Rated Power", "value": "1800 watts" }, { "name": "Brush Width", "value": "380mm" }, { "name": "Working Depth", "value": "+6mm to -12mm" }, { "name": "Brush Rotation Speed", "value": "3500 rpm" }, { "name": "Sound Pressure Level", "value": "LPA=90.2 db(A)" }, { "name": "Guaranteed Sound Power Level", "value": "LWA=108 db(A)" }, { "name": "Weight", "value": "13.15 kg" }, { "name": "Power Cord Length", "value": "12 meters" }, { "name": "Basket Size", "value": "50 liters" } ], "name": "T-Mech Artificial Grass Vacuum", "label": "Buy", "description": "Thank you for purchasing the T-Mech Artificial Grass Vacuum. This lightweight but powerful vacuum is great for maintaining your artificial grass. It will lift the pile while removing twigs, leaves, and weeds. Five height settings allow the vacuum to be adjusted for all styles of artificial grass. \n\nFor maximum convenience, this vacuum comes with an extra-long 12-meter power cable and a 50 litre collection basket. \n\nSo, what are you waiting for? Improve the lifespan of your artificial grass and ensure it looks its very best at all times." } } ], "cover": { "title": "T-Mech Artificial Grass Vacuum", "description": "Refresh your artificial grass with the T-Mech garden vacuum. With a 3500RPM brush, 5 height settings, 50L bag, and 1800W suction, it removes debris and lifts fibres with ease. Self-propelled, lightweight, and perfect for lawns, paths, and driveways.", "image": { "path": "images/a604705fb288bc18.jpg", "alt": "" } } }